BUILT FOR BUILDERS.
BY BUILDERS.
innovative moto tools FOR THE PASSIONATE BUILDERS.
Featured Products
Struggling to find a way to store motorcycle forks ready to be serviced, or waiting to go back to the customer? With the CBB3D “Fast Fork Storage” system, quickly and easily store and remove forks on the wall. The Fast Fork Storage was designed with suspension shops in mind, dealing with large amounts of forks day in and day out. The Fast Fork Storage system is a two piece design, with the top piece being a “snap” design, and the bottom piece supporting the weight of the forks, and also offering a removable drain pan to collect leaking fork oil, keeping your shop floors clean.
What makes this system so fast? The design. There’s no struggling with locking plates, clamps, or screws to remove the forks. To install the forks, simply center and rest the bottom valve of the fork on the standoff located on the drain pan, the push the top of the fork into the top snap bracket, and the fork is secure. Installation is so easy it can be done with one arm! To remove the forks, its as easy as pulling the fork out of the top clamp, and lifting it off the bottom bracket.
There’s no more need to worry about fork oil covering the shop floor. With the fast fork holder, the included removable drain pan will catch all of the fork oil that runs down, neatly contained in the bottom pan. Once the pan is full, remove the pan by pulling up, and dump into your oil collection containers. The oil catch pan is secured to the bracket using two alignment dowels, and two strong magnets, giving a very secure hold, while offering quick removal and installation of the pan.
The Fast Fork Holder will fit a wide variety of forks.
MINIMUM OUTER FORK TUBE DIAMETER: 46MM
MAXIMUM OUTER FORK TUBE DIAMETER: 59MM
-Please read the install instructions for this product, especially if you are buying multiple fork holders. Its mandatory the holders are installed correctly for proper function!
Plastic Feet shown in pictures are not part of the Fast Fork Holder. This is only to hold up the bottom bracket for taking pictures!
If you plan to buy 3+ Fast Fork Holders, please reach out via the contact email on the site. I offer a bulk order discount!
Tired of doing routine oil changes on your bike with only one hand and spilling oil? The CBB3D threaded oil funnel set solves that issue by allowing the funnel to thread into the crankcase of the bike, freeing up a hand and leading to a much cleaner and easier oil change. The threaded funnel set come with a variety of adapters to fit most makes and models of bikes, as well as 30 degree offset connectors, for those hard to reach oil fill plugs. Included in the kit is a wall mount holder for the funnel, extension, and all included adapters with a convenient drain pan that slots into the bottom of the holder, keeping the mess of residual oil left in the funnel leaking onto your floor. Make servicing your bike easier with the CBB3D Threaded Oil Funnel Set.
Adapters included in this kit:
(1): M16X2.0 Straight Adapter
(1) M18X1.5 Straight Adapter
(1)M20X2.5 Straight Adapter
(1) M24X3.0 Straight Adapter
(1): M16X2.0 Angled Adapter
(1) M18X1.5 Angled Adapter
(1)M20X2.5 Angled Adapter
(1) M24X3.0 Angled Adapter
(1) 4” Funnel Extension
THIS TOOL IS COVERED BY A LIFETIME WARRANTY. ANY ISSUES PLEASE CONTACT CBB3DHELP@GMAIL.COM AND WE WILL SEND OUT REPLACEMENT FUNNEL PARTS
One of the most crucial areas of maintenance on your bike is the steering stem bearing. Many times the maintenance on the steering stem bearing is forgotten or brushed over, leading to hard or seized steering. With this steering stem grease tool, simply slide the tool over the steering stem, attach your grease gun to the included grease fitting, apply grease until the grease just starts to come out the bottom of the tool, rotate the tool around the bearing a couple times, and its good to go!
Please select model of bike below. The Japanese stem greaser will not work for Austrian bikes and vise versa.
Works with most Japanese dirt bikes. Please confirm lower bearing outside diameter is 50MM +-1, and steering stem OD is 30MM
Works with most Austrian dirt bikes. Please confirm lower bearing outside diameter is 50MM +-1 and steering stem OD is 29MM
Material: PETG+
BUILT FOR BUILDERS.
We’ve all been there, your bike is in pieces, and all your parts are finally rolling in. You cant wait to get your bike together, only to be slowed down or stopped because you’re missing the right tool for the job, or simply, it doesn’t exist.
Our goal at CBB3D is to provide high quality 3D printed moto tools for passionate builders, mechanics, and DIYers. We strive to design useful tools that have been lacking in the moto industry.
Reviews
